Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Ici vous trouverez les présentations issues des Conférences COMSOL à travers le monde. Réalisées par des utilisateurs de COMSOL Multiphysics, ces présentations explorent tous les domaines actuels d'innovation. Les applications couvrent pratiquement tous les secteurs industriels et impliquent des phénomènes électriques, mécaniques, fluidiques et chimiques. Utilisez la recherche rapide pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Thin Microchip Release From a Carrier Tape: Structural Mechanics and Vacuum Forces

S. Behler[1]
[1]Besi Switzerland AG, Switzerland

During semiconductor manufacturing, finished silicon microchips need to be released from a carrier tape they stick to by an adhesive. This is done by vacuum forces that (a) hold the chip flat from above and (b) pull the tape off from the chip underside. Sounds simple, but is very tricky ... En savoir plus

Flow Induced Oscillations of Marine Risers with Wake Interference

F. Van den Abeele, and J. Vande Voorde
OCAS N.V., J.F. Kennedylaan 3, Zelzate, Belgium

With offshore oil and gas exploration and production moving into ever deeper waters, the suspended length of marine risers (transporting hydrocarbons from the seabed to the surface) can easily exceed 3000 meters. One of the major design requirements for risers in (ultra) deep water is to ... En savoir plus

Flotation Height in 'Air Hockey' Spatial Atomic Layer Deposition

J. Grasso [1], B. Willis [1],
[1] Department of Chemical and Biomolecular Engineering, University of Connecticut, Storrs, CT, USA

Atomic layer deposition(ALD) is one proven method to deposit ultra-thin films. ALD is advantageous for its atomic-level thickness control and conformity; leading to high quality films. Slow deposition rates for conventional ALD contribute to the impracticality of utilization of this ... En savoir plus

Modelling of a Single Cardiomyocyte Interaction with a Microcantilever Using COMSOL Multiphysics®

I. Banerjee[1]
[1]Tampere University of Technology, Tampere, Finland

: One of the most commonly used techniques for quantification of beating forces exerted by cardiomyocytes is culturing them on a bed of vertical microcantilevers or microposts. The position of the microcantilevers is observed through advanced imaging techniques and the displacements are ... En savoir plus

Proof of Concept and Properties of Micro Hydraulic Displacement Amplifier

R. Zhu[1], A. Malisauskaite[1], U. Mescheder [1], U. Wallrabe[2]
[1]Hochschule Furtwangen University, Furtwangen, Baden-Württemberg,Germany
[2]Institut für Mikrosystemtechnik (IMTEK), Freiburg, Baden-Württemberg, Germany

Nowadays, mathematical models have been widely applied in varies fields; especially in fluid mechanics and nonlinear material which are very complex or even not possible to be calculated using analytical methods. In this paper, a hydraulic displacement amplifier coupled with fluid ... En savoir plus

Energy Harvesting from Variation in Blood Pressure through Deformation of Arterial Wall using Electro-magneto-hydrodynamics

A. Pfenniger[1], V.M. Koch[2], A. Stahel[2], and R. Vogel[1]
[1]ARTORG Cardiovascular Engineering, University of Bern, Bern, Switzerland
[2]Bern University of Applied Sciences, Engineering and Information Technology, Biel, Switzerland

The present project aims at modelling a generator that harvests energy from the variation in blood pressure by exploiting the motion of the arterial wall between the diastolic and systolic phase of the cardiac cycle. The concept is to use a highly electrically conductive fluid, which is ... En savoir plus

Finite Element Modeling of a Cell Lysing Chip

S. Maloney[1,2], Y. Li[1,2], G. Auner[1], and J. Smolinski[1]
[1]Wayne State University, Detroit, MI, USA
[2]Lawrence Technological University, Southfield, MI, USA

We are working on a microfabricated lysing chip that uses a piezoelectric actuator to provide ultrasonic energy to break apart cells. The device contains pillars with varying dimensions. We hypothesize that increasing the aspect ratio of pillars will increase the efficiency of the ... En savoir plus

Optimization of Extrusion Processes for non-Newtonian high-Viscous Fluids with Wall Slip and Shear Thinning Effects

W. Hoffmann[1], M. Scholz[1]
[1]SiCo-Solutions, Stuttgart, Germany

Simulation of the flow behaviour of non-Newtonian fluids with high viscosities leads to special material models with specific material parameters. In this presentation, a material model consisting of 4 material parameters describing the flow itself and also the wall slip is presented. ... En savoir plus

Using COMSOL Multiphysics^® for Biomechanical Analysis of Stent Technology in Cerebral Aneurysms

J. Rasmussen[1], M.S. Enevoldsen[1], J. Thyregod[2], and K-A. Henneberg[1]
[1]Department of Electrical Engineering, Technical University of Denmark, Kgs. Lyngby, Denmark
[2]COOK Medical Europe, Bjaeverskov, Denmark

This work presents new Fluid-Structure Interaction (FSI) models in both 2D and 3D of the effect of using vascular stents as treatment of cerebral berry aneurysms. The stent is positioned inside the cerebral artery covering the neck of the aneurysm. The stent is expected to alter the ... En savoir plus

FSI Analysis of Microcantilevers Vibrating in Fluid Environment

A. Ricci[1] and E. Giuri[1]

[1]Materials and Microsystems Laboratory (CHI-Lab), Politecnico di Torino, Torino, Italy

Cantilever vibration in fluid environment is probably one of the most common Fluid Structure Interaction problems in the field of Micro/Nano Electro Mechanical Systems. Usually the effect of fluid on cantilever oscillation is characterized in terms of mode resonance frequencies and ... En savoir plus

Premier

71–80 of 185

Dernier