Articles techniques et présentations

Recherche rapide

Ressources

Livres Blancs

Voyez comment la modélisation et la simulation sont utilisées par les industries La modélisation et la simulation multiphysiques pilotent l'innovation dans tous les grands secteurs d'activité et dans le monde universitaire — comme en témoignent les nombreuses utilisations présentées dans des articles et des posters techniques présentés par des ingénieurs, chercheurs et scientifiques à la Conférence COMSOL chaque année. Inspirez-vous des récents proceedings réunis ci-dessous, ou, pour trouver les présentations les plus intéressantes dans votre domaine d'intérêt, utilisez la recherche rapide.

Consultez les proceedings de la Conference COMSOL 2024

Terme recherché:

Deformation Behavior Of A Liquid Droplet Impacting A Solid Surface

S. Oukach[1], M. Elganaoui[1], B. Pateyron[1], and H. Hamdi[2]
[1]Laboratoire des Sciences des Procèdes Céramiques et de Traitements de Surface SPCTS, Limoges, France
[2]Laboratoire de Mécanique des Fluides et Energétique LMFE, Marrakech, Morocco

The quality of coatings obtained by means of thermal spraying depends strongly on the mechanism of the interaction between the molten droplets and the surface to be covered. The aim of the present study is to simulate the impact of a droplet onto a substrate, in order to have a good ... En savoir plus

Heat Transfer Modeling and Analysis of a Rotary Regenerative Air Pre-heater

R. K. Krishna, R. Ramachandran, and P. Srinivasan
Birla Institute of Technology and Science
Pilani
Rajasthan, India

An attempt has been made to sustain the efficiency of an air pre-heater(APH) in the long run. The APH is modeled using COMSOL Multiphysics in 3D and fed with real life conditions. Upon Heat transfer analysis, the temperature profile was found out and from that, the regions undergoing ... En savoir plus

A Modular Platform for Cell Characterization, Handling, and Sorting by Dielectrophoresis

S. Burgarella[1], B. Dell’Anna[2], V. Perna[1], G. Zarola[2], and S. Merlo[2]

[1]STMicroelectronics, Agrate Brianza, MI, Italy
[2]Dipartimento di Elettronica, Università degli Studi di Pavia, Pavia, Italy

Dielectrophoresis (DEP) is a method for cell manipulation without physical contact in lab-on-chip devices, since it exploits the dielectric properties of cells suspended in a microfluidic sample, under the action of locally generated high-gradient electric fields. The DEP platform that ... En savoir plus

Including Expert Knowledge in Finite Element Models by Means of Fuzzy Based Parameter Estimation

O. Krol[1], N. Weiss[1], F. Sawo[1], and T. Bernard[1]

[1]Fraunhofer Institute for Information and Data Processing, Karlsruhe, Germany

In this paper we present a novel approach for modeling spatial distributed bio- chemical and environmental processes like the growth of plants and the related biochemical reactions. The physical phenomena like flow and mass transport can be described by fluid dynamics equations, but for ... En savoir plus

Complex Geometry Creation and Turbulent Conjugate Heat Transfer Modeling

I. Bodey[1], R. Arimilli[1], and J. Freels[2]
[1]Dept. of Mechanical, Aerospace and Biomedical Eng., The University of Tennessee, Knoxville, TN
[2]Research Reactors Division, Oak Ridge National Laboratory, Oak Ridge, TN

The High Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory (ORNL) is an 85 MW, light-water moderated, research reactor that operates at low temperature and high pressure. The HFIR is presently scheduled to convert from a high enriched uranium fuel (HEU) to a low enriched ... En savoir plus

A MEMS Condenser Microphone for Consumer Applications

S. L. Pinjare, V. S. Nagaraj, S. N. Savitha, S. Kesari, M. S. Sagar, and K. R. Roshan
Nitte Meenakshi Institute of Technology

The MEMS microphone is also called microphone chip or silicon microphone. The pressure sensitive diaphragm is etched directly into a silicon chip by MEMS techniques and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone ... En savoir plus

Design and Optimization of Gas Sensor Testing Chamber using COMSOL Multiphysics®

K.Govardhan[1], K.Narmada[2], Nirmala Grace[3]
[1]VIT University, MEMS & Sensors Division, School of Electronics Engineering, Vellore, Tamil Nadu, India
[2]VIT University, Sensor System Technology, School of Electronics Engineering, Vellore, Tamil Nadu, India
[3]VIT University, Center for Nanotechnology Research, Vellore, Tamil Nadu, India

This study aims at the design and optimization of a Gas Sensing Chamber. The design takes advantage of the multiphysics simulation capabilities of COMSOL Multiphysics® to incorporate various physics such as CFD, Micro fluidics, Solid Mechanics, Electro thermal effects etc. The ... En savoir plus

Modeling Void Drainage with Thin Film Dynamics

J.J. Gangloff Jr.[1], W.R. Hwang[2], S.G. Advani[1]
[1]Center for Composite Materials, Department of Mechanical Engineering, University of Delaware, Newark, DE, USA
[2]School of Mechanical Engineering, Gyeongsang National University, Jinju, Gyeongsangnam-do, Korea

Voids in composite materials can lead to degraded structural performance. The following is a study of voids or bubbles in uncured viscous polymer resin during composites processing. The goal is to determine if voids can successfully migrate towards vacuum pathways, coalesce with the ... En savoir plus

Flow Analysis and Optimization of a Hierarchical Plate Heat Exchanger for an Adsorption Heat Pump

E. Tempfli[1], F.P. Schmidt[1]
[1]Karlsruhe Institute of Technology (KIT), Fluid Machinery (FSM), Karlsruhe, Germany

The paper investigates the hydrodynamic performance of a hierarchical parallel channel network for the objective of optimal thermal coupling to heat released in the adsorption processes, as in adsorption heat pumps. More specifically, the uniformity of the fluid flow over the network is ... En savoir plus

Modification of the Ion Angular Distribution in Plasma Sheath: Modeling Approach under COMSOL Multiphysic

J. Brcka
TEL US Holdings, Albany, NY, USA

System for in-situ control of the ion angular distribution function (IADF) in plasma reactor is modeled. Typical IADF depends on the pressure, bias and excitation frequency. It is formed due to a difference in the physical properties of the plasma and sheath domains. The IADF is modified ... En savoir plus

Premier

711–720 of 931

Dernier