Menu

Discussion Forum

New Discussion
Filtrer

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

What does 'Compute Implicit Height Change From Base Velocity' mean in the Thin Film Flow module?

Posted 2 janv. 2024, 11:40 UTC−5 Fluid & Heat, Computational Fluid Dynamics (CFD), User Interface Version 6.1 2 Replies

Jake Liu
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Dear all,

I am trying to predict the experimental results of plain bearings with the COMSOL thin film flow module. However, I am confused by the option 'Compute Implicit Height Change From Base Velocity' in Fluid-Film Properties, which is not explained in the documentation and can have a significant impact on the results. (The attachment shows the location of this option)

What does 'Compute Implicit Height Change From Base Velocity' mean in the Thin Film Flow module?

Thanks in advance.

The same question has been asked before but not answered:

The below post is related to an archived discussion

Attachments:

2 Replies Last Post 5 janv. 2024, 13:04 UTC−5
Mats Nigam COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 11 months ago 5 janv. 2024, 12:23 UTC−5
Updated: 11 months ago 5 janv. 2024, 12:26 UTC−5

Dear Jake,

I regret that this had not been documented. I have added the documentation which will be included in future versions of COMSOL. When a user-defined wall or base velocity is specified, it induces a "squeezing" effect on the flow which results in an effective mass source. If, for example, the base moves with velocity , the implicit height change becomes,

where the first part comes from the motion normal to the reference plane and the second part is due to topology changes of the base. This results in an effective mass source on the right hand side of the continuity equation,

and correspondingly for the wall velocity.

Best regards, Mats

Dear Jake, I regret that this had not been documented. I have added the documentation which will be included in future versions of COMSOL. When a user-defined wall or base velocity is specified, it induces a "squeezing" effect on the flow which results in an effective mass source. If, for example, the base moves with velocity {\bf v}_{b} , the implicit height change becomes, \frac{\partial h_{b}}{\partial t}={\bf v}_{b}\cdot{\bf n}_{ref}-{\bf v}_{b}\cdot\nabla_{t}h_{b} where the first part comes from the motion normal to the reference plane and the second part is due to topology changes of the base. This results in an effective mass source on the right hand side of the continuity equation, Q_{b}^{eff}=-\rho({\bf v}_{b}\cdot{\bf n}_{ref}-{\bf v}_{b}\cdot\nabla_{t}h_{b}) and correspondingly for the wall velocity. Best regards, Mats
Jake Liu
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 11 months ago 5 janv. 2024, 13:04 UTC−5
Updated: 11 months ago 5 janv. 2024, 14:48 UTC−5

Dear Mats,

Thank you for your reply. I didn't fully understand the second part, but it sounds like it's an option that should be enabled all the time (similar to the concept of inertial forces), could you tell me when it should be turned off? After testing, I've found that enabling this option always tends to overestimate the pressure (several times greater than not enabling it), even if the film is thick.

Also, I don't find this option in the hydrodynamic bearing module (in theory it is the same as the Thin Film Flow module), is it enabled by default?

I’m sorry for asking so many questions. I appreciate your time in responding to whatever you can, when you are able to find the time.

Best regards,
Jake

Dear Mats, Thank you for your reply. I didn't fully understand the second part, but it sounds like it's an option that should be enabled all the time (similar to the concept of inertial forces), could you tell me when it should be turned off? After testing, I've found that enabling this option always tends to overestimate the pressure (several times greater than not enabling it), even if the film is thick. Also, I don't find this option in the hydrodynamic bearing module (in theory it is the same as the Thin Film Flow module), is it enabled by default? I’m sorry for asking so many questions. I appreciate your time in responding to whatever you can, when you are able to find the time. Best regards, Jake

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content