Menu

Discussion Forum

New Discussion
Filtrer

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

pulse generation

Posted 26 avr. 2012, 08:47 UTC−4 Low-Frequency Electromagnetics, Heat Transfer & Phase Change Version 4.2a 3 Replies

Mohammad Arif Saber
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi,

I am new to comsol and I want to generate a single pulse of 0.7 v of 20us . this will act as a voltage to a structure and the structure will get heated up. Now my point is to see how fast the structure cools down.

I have no idea how to do this. what I did is defined a rectangle function with lower limit as 20 us and upper limit as 40 us and then i try to use 0.7*rect1(t1) as a input voltage. I tried to follow the suggestion in the other threads but could not understand. Can anybody help me? BTW I am using V4.2a.
3 Replies Last Post 30 avr. 2012, 13:57 UTC−4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 26 avr. 2012, 14:34 UTC−4
Hi

the rect() or pulse function, just as he step function has a rise time defined in the dvanced tab (normally "closed") you need to adapt this parameter too when you have such short pulses, do not make it too steep, or then at least define enough time stepping (or parameter stepping) points in the solver definition to catch the rise time (I would say at least 5 step during the rise and fall time. If you are doing time dependent studies, as I understand, check also the solver stepping settings and use an "intermediate" and NOT automatic stepping scheme, as you have a rise and a fall time here. Then if the default BDF does not converge, you could also try the Gen-alpha solver, it's sometimes more stable, but often somewhat slower, all depends ...

--
Good luck
Ivar
Hi the rect() or pulse function, just as he step function has a rise time defined in the dvanced tab (normally "closed") you need to adapt this parameter too when you have such short pulses, do not make it too steep, or then at least define enough time stepping (or parameter stepping) points in the solver definition to catch the rise time (I would say at least 5 step during the rise and fall time. If you are doing time dependent studies, as I understand, check also the solver stepping settings and use an "intermediate" and NOT automatic stepping scheme, as you have a rise and a fall time here. Then if the default BDF does not converge, you could also try the Gen-alpha solver, it's sometimes more stable, but often somewhat slower, all depends ... -- Good luck Ivar
Mohammad Arif Saber
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 30 avr. 2012, 03:35 UTC−4
Hi Ivar,

Thanks a lot for your reply. I started reading the user's guide after your reply but could not find any advanced tab. how can I activate this advanced tab ?
Hi Ivar, Thanks a lot for your reply. I started reading the user's guide after your reply but could not find any advanced tab. how can I activate this advanced tab ?
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 30 avr. 2012, 13:57 UTC−4
Hi

my fault it's not the advanced it's the "smoothing" tab (I get also confused, and I'm not always behind my WS ;)

You are right that many of the "advanced" tabs are hidden,by default you must turn them on from the the Options Preferences View tab

--
Good luck
Ivar
Hi my fault it's not the advanced it's the "smoothing" tab (I get also confused, and I'm not always behind my WS ;) You are right that many of the "advanced" tabs are hidden,by default you must turn them on from the the Options Preferences View tab -- Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content