Menu

Discussion Forum

New Discussion
Filtrer

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Where do you set the 'depth' of 2D model in 4.2a?

Posted 12 avr. 2012, 23:56 UTC−4 Version 4.2a 4 Replies

Sheng Zhang
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Before 4.x I used to set the 'depth' (z-axis) of a 2D model in subdomain setting. Where is it in 4.2a?

Thanks!
4 Replies Last Post 17 avr. 2012, 16:14 UTC−4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 13 avr. 2012, 11:38 UTC−4
Hi

if the depth applies (not always the case), it's generally found in the main physics node

--
Good luck
Ivar
Hi if the depth applies (not always the case), it's generally found in the main physics node -- Good luck Ivar
Yu-Hsin Liu
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 17 avr. 2012, 12:24 UTC−4

Hello~

I'm new for the Comsol simulation, and have the similar question about the depth of 2D model.
May I ask what's the original value that Comsol set of the depth (at z-axis) for the 2D model? Also, where can I change the value in 3.5 version? Thank you so much!
Hello~ I'm new for the Comsol simulation, and have the similar question about the depth of 2D model. May I ask what's the original value that Comsol set of the depth (at z-axis) for the 2D model? Also, where can I change the value in 3.5 version? Thank you so much!
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 17 avr. 2012, 14:21 UTC−4
Hi

in most cases (but not always, pls check carefully ;) the default depth is 1[m] which means that everything in 2D is "per meter".

Unfortnately, it's too long since I last used 3.5, I just cannot remember, try to check the doc (I usually index my pdf, then search for "depth")

--
Good luck
Ivar
Hi in most cases (but not always, pls check carefully ;) the default depth is 1[m] which means that everything in 2D is "per meter". Unfortnately, it's too long since I last used 3.5, I just cannot remember, try to check the doc (I usually index my pdf, then search for "depth") -- Good luck Ivar
Sheng Zhang
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 17 avr. 2012, 16:14 UTC−4

Hello~

I'm new for the Comsol simulation, and have the similar question about the depth of 2D model.
May I ask what's the original value that Comsol set of the depth (at z-axis) for the 2D model? Also, where can I change the value in 3.5 version? Thank you so much!


In 3.5, it's in the subdomain physics setting.
[QUOTE] Hello~ I'm new for the Comsol simulation, and have the similar question about the depth of 2D model. May I ask what's the original value that Comsol set of the depth (at z-axis) for the 2D model? Also, where can I change the value in 3.5 version? Thank you so much! [/QUOTE] In 3.5, it's in the subdomain physics setting.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content