Menu

Discussion Forum

New Discussion
Filtrer

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Simulation of a Metallic CUBE

Posted 10 mai 2011, 06:21 UTC−4 RF & Microwave Engineering Version 3.5a 10 Replies

Cecil Chalmers
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Dear Users,
I am trying to simulate a gold nano cube in air. I have drew a 40nm cube from the draw menu. Then i enclosed by it by a spherical surface which contain air.
Now my question is that, how to smoothened the sharp corners (edges) of a cube?
Does the comsol automatically smooths its edges by enclosing it in a sphere or i have to do some trick?

Regards,
Cecil.
10 Replies Last Post 4 déc. 2015, 09:34 UTC−5
Edgar Kaiser
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 10 mai 2011, 07:23 UTC−4
Hi,

in COMSOL you can do mathematical operations with your objects. You can add, subtract and do boolean operations.
So, you can use a boolean AND on your cube and a sphere that is a little smaller than the diagonal of the cube to cut the sharp corners away. There may be more options depending what exactly you want.

Cheers
Edgar
Hi, in COMSOL you can do mathematical operations with your objects. You can add, subtract and do boolean operations. So, you can use a boolean AND on your cube and a sphere that is a little smaller than the diagonal of the cube to cut the sharp corners away. There may be more options depending what exactly you want. Cheers Edgar
Cecil Chalmers
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 10 mai 2011, 09:03 UTC−4
Hi,
Many thanks for your reply.

I followed your method (if i am correct), i.e. 1st of all i draw a sphere, then a cube. The sphere is a little bit smaller than the diagonals of the cube. Then i went to the draw menu. I selected the "Create Composite Object" and there i took an interaction of both the sphere and the cube. I obtained the figure given in the attachment.
I don't know whether it is correct or not and also this figure is a mixture of both the cube and sphere. Will it effect the results?

Best Regards,
Cecil.
Hi, Many thanks for your reply. I followed your method (if i am correct), i.e. 1st of all i draw a sphere, then a cube. The sphere is a little bit smaller than the diagonals of the cube. Then i went to the draw menu. I selected the "Create Composite Object" and there i took an interaction of both the sphere and the cube. I obtained the figure given in the attachment. I don't know whether it is correct or not and also this figure is a mixture of both the cube and sphere. Will it effect the results? Best Regards, Cecil.

Attachments:

Edgar Kaiser
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 10 mai 2011, 09:44 UTC−4
Cecil,

your sphere diameter is still significantly smaller than the diagonal of the cube. I mean the space diagonal through the center not the diagonal of one of the faces. You can now play a little and grow the sphere until you get something that looks like a cube with kind of cut away corners.

At the end you must decide by yourself if the geometry meets your requirements and you will need to apply appropriate procedures to validate your FE model.

Cheers
Edgar
Cecil, your sphere diameter is still significantly smaller than the diagonal of the cube. I mean the space diagonal through the center not the diagonal of one of the faces. You can now play a little and grow the sphere until you get something that looks like a cube with kind of cut away corners. At the end you must decide by yourself if the geometry meets your requirements and you will need to apply appropriate procedures to validate your FE model. Cheers Edgar
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 10 mai 2011, 10:27 UTC−4
Updated: 4 years ago 5 janv. 2021, 10:29 UTC−5
If you are trying to fillet the edges (not just round the vertices) of your cube, you can achieve that by filleting a square in a workplane, extruding that, making two copies of that extruded object, moving and rotating them appropriately and taking the intersection of those three objects, see the attached screen shot.
If you are trying to fillet the edges (not just round the vertices) of your cube, you can achieve that by filleting a square in a workplane, extruding that, making two copies of that extruded object, moving and rotating them appropriately and taking the intersection of those three objects, see the attached screen shot.

Attachments:

Cecil Chalmers
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 10 mai 2011, 11:45 UTC−4
Jean,
I want the same model, which you showed me. Can you please explain it a little more (parameters etc) as i am using comsol 3.5a.
Thanks.

Regards,
Cecil
Jean, I want the same model, which you showed me. Can you please explain it a little more (parameters etc) as i am using comsol 3.5a. Thanks. Regards, Cecil
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 10 mai 2011, 14:00 UTC−4
There's nothing to it, really. In a workplane you just create a square and fillet its corners. Then you extrude that shape; that gives you a square column with rounded edges. You make two copies and rotate them 90 degrees so that the three columns are aligned with the x,y, and z axes. Finally you move them so their intersection is the dice you are after, and take the intersection.
If you update to 4.1 I can send you the mph file.
There's nothing to it, really. In a workplane you just create a square and fillet its corners. Then you extrude that shape; that gives you a square column with rounded edges. You make two copies and rotate them 90 degrees so that the three columns are aligned with the x,y, and z axes. Finally you move them so their intersection is the dice you are after, and take the intersection. If you update to 4.1 I can send you the mph file.
Cecil Chalmers
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 18 mai 2011, 13:01 UTC−4
Hi jean,
I have now installed Comsol 4.1. Can you send me the mph file.

Thanks.

BR,
Cecil
Hi jean, I have now installed Comsol 4.1. Can you send me the mph file. Thanks. BR, Cecil
MicroXact
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 17 oct. 2011, 16:07 UTC−4
Hi Jean,

Could you send to me a copy as well? I have made it to the point where intersection operation occurs

I have version 4.2.
Hi Jean, Could you send to me a copy as well? I have made it to the point where intersection operation occurs I have version 4.2.
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 18 oct. 2011, 07:03 UTC−4
Hi

follow the steps under the model builder geoemtry tab, of the dice.png picture, and you will find out ;)

--
Good luck
Ivar
Hi follow the steps under the model builder geoemtry tab, of the dice.png picture, and you will find out ;) -- Good luck Ivar
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 4 déc. 2015, 09:34 UTC−5
Update on this thread: Nowadays COMSOL includes a 3D fillet capability in the Design Module. See www.comsol.com/design-module
Best,
Jeff
Update on this thread: Nowadays COMSOL includes a 3D fillet capability in the Design Module. See http://www.comsol.com/design-module Best, Jeff

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content